When a furnace won’t turn on, the cause is often something simple: the thermostat, the power switch, a clogged filter, the fuel supply or a safety switch that has shut the system down. A few minutes of checking can sometimes get the heat back on, and if it doesn’t, what you found helps us arrive ready. Noble’s Heating & Cooling services gas, oil and propane furnaces throughout the Lehigh Valley and the Poconos from our base in Saylorsburg. Here’s what to look at first, and what to leave alone.
Seven Things You Can Safely Check
- The thermostat. Make sure it’s set to Heat, not Cool or Off, and set a few degrees above the current room temperature. If the screen is blank or dim, replace the batteries. Many thermostats stop calling for heat when the batteries run low.
- The power switch. Most furnaces have a service switch that looks like a light switch, either on the side of the furnace or on the wall nearby. On many oil systems it has a red cover plate and sits at the top of the basement stairs, where it’s easy to flip off by mistake. Also check the breaker panel for a tripped breaker.
- The furnace door. The panel over the blower has a safety switch behind it. If the panel isn’t seated properly, often after someone changed the filter, the furnace won’t run. Press it firmly back into place.
- The filter. A badly clogged filter can make the furnace overheat and shut itself off. Our post on how often to change your furnace filter walks through checking and replacing it.
- The fuel. For gas, make sure the gas valve at the furnace is open and that other gas appliances are working. For oil or propane, check the tank gauge. An empty tank can look exactly like a broken furnace.
- The condensate drain. High-efficiency gas furnaces, the ones with white plastic vent pipes, produce water as they run. It drains through a tube or into a small pump. If the pump is full or the line is clogged or frozen, a safety switch stops the furnace. Water on the floor near the furnace is a common clue.
- The reset button on an oil burner. If the red reset button on the burner is lit or popped out, you can press it once. If the burner starts and keeps running, keep an eye on it and give us a call to find out why it locked out. If it doesn’t start, don’t press it again.
What Not to Do
The reset button deserves its own warning. Each press sends oil into the combustion chamber, and if the burner doesn’t light, that oil stays there. After several presses, enough can build up that it ignites all at once when the burner finally fires. One press is the limit. After that, it’s time for a technician.
A few other rules for a cold night:
- Don’t tape down, bypass or disconnect any switch on the furnace to make it run.
- Don’t use the kitchen oven or stovetop to heat the house.
- If you smell gas, leave the house and call your gas utility or propane supplier from outside. Don’t flip switches or use the phone inside.
- Keep portable heaters away from curtains, bedding and furniture, and never leave them running unattended.
When It’s Time to Call
Call us if none of the checks above got the furnace running, or if you notice any of these:
- The furnace starts, runs a few minutes and shuts off again.
- The blower runs but the air coming out of the vents is cold.
- The breaker trips again after you reset it.
- You hear new grinding, banging or screeching, or smell burning beyond the light dust smell of the first startup of the season.
- The oil burner locks out again after one reset.
When you call, it helps to tell us what fuel you heat with, what the thermostat shows, and what you’ve already checked. That way we can bring the right parts.
After Hours and in Freezing Weather
Heating problems don’t keep business hours. Our office hours are Monday through Friday, 8 to 5, and we take calls outside those hours too. We’ll ask a few questions about what your system is doing and help you decide whether it’s safe to wait until morning. Customers we already service get priority, and a home without heat in freezing weather always gets our first attention.
Preventing the Next No-Heat Call
ENERGY STAR recommends checking thermostat settings, filters and the system’s controls as part of regular maintenance. Many of the no-heat calls we see in January start as a dirty flame sensor, a worn ignitor or a clogged oil nozzle that a fall tune-up would have caught. Learn more about our furnace repair and maintenance services, or call Noble’s Heating & Cooling at 484-860-2055. Our $120 diagnostic fee covers the first half hour on site, which is usually enough time to find the problem.